Alexandr A.Shpilman (alexandrshpilman78@gmail.com )
The Converter
In "Branchy lightning of thought"
expressed idea that round us there is something that influences the form of a
high-voltage electric spark. What it, "Dark matter" of
astrophysicists? DSS elements?
If it DSS
elements, in certain rather inert form (will quite fit under "Dark
matter"), such that only high electric voltage uncollapsed
them Such as it is used in "The Imitator of a
"Place Power" IPP-4i", or it is not less of that that was
used in "Branchy lightning of
thought". However, it is not clear yet, what role in uncollapsed is played by a high intensity of electric field
and a difference of electric potentials.
In "Separation
Axion (Spin) Field" were used electric voltage of 20-300V.
A thickness dielectric between lead plates about 0.03 mm. From
here intensity of electric field 6*10^5 – 10^7 V/m.
Instead of lead plates it is possible to try to
use a copper wire in diameter of 0.1 mm and thickness of its varnish covering
approximately 0.01 mm. In this variant between two such braided conductors, at
electric potential between them in 300Vt, we will have the maximum intensity of
electric field of an order 1.5*10^7 V/m. (Intensity of a field of electric
breakdown of air of an order 10^6 V/m).
Here we
can assume the following theoretical model:
Pseudo-positive
a component 2 of DSS an element 1 is guided towards a conductor 4 having
negative electric potential (the Fig.1 see). And
pseudo-negative a component 3 is guided towards a conductor 5 having positive
electric potential.
|
Fig.1 |
Fig.2 |
If we pass now through conductors 4
and 5 electric current I1 and I2 as it is shown in a Fig.2
"pseudo-charged" components of DSS elements, being extended
towards to a direction of an electric current, will start to merge in two dense
plaits. Thus "dumping" surplus of energy resulted uncollapsed
DSS elements.
The interesting situation will be
when we will close conductors 4 and 5 in near located two rings. It is possible to expect that two plaits of the
elements "pseudo-charged" component DSS at some instant, having
reached critical density, will be drawn and will be closed between itself
according to effect shown on a Fig.4 and 5 "Separation
Axion (Spin) Field" in cyclically closed cluster on similarity shown on a Fig.3.
|
Fig.3 |
|
Photo 1 |
|
Photo 2 |
As such short circuit of plaits of
"pseudo-charged" components of DSS elements has overcome electric
potential between conductors last will not be probable for keeping formed
cluster, and it will be compressed in a compact particle which more can leave
our design from conductors any more less freely. It is necessary to hope that
the new particle from cluster DSS elements will be less inert than "collapsing"
DSS elements.
Now we will think of an
experimental design.
The
conductors closed in a ring it is possibly to replace in two hardly braided
conductors in enamel isolation as in the Photo 1. Attention that to a photo
left twisting of wires. As have shown experiments, it meaning. Possibly, at
such twisting similarity "Lissajous
figures" than simply ring structures of the cluster of DSS elements are
more likely formed.
In
continuation, we will twist our cord from two wires into a ring more
represented on the Photo 2. We will place inside a cardboard cup with water and
we will make experiment on themselves and voluntary "rabbits" (as to
measure result while there is nothing).
The result see in article "
Experiments with converter of DSS elements ".
In experiment the plait from two conductors in varnish isolation in diameter
of 0.12 mm, length 11 m. was used. Counter
current in wires - 120 мА.
Voltage between conductors 295V. The plait had been
reeled up a ring to a ring the coil in diameter of 60 mm (it is covered by a
thin layer of colophony dissolved in alcohol). In the coil the cup with 50
milliliters of water was put. Time of an exposition of 10-15
minutes.
In the further development of a
design, we reel up the eight, on a wire aluminium
skeleton, separately a plait with left and right
twisting wires, as is shown in the Photo 3, and it is placed in shielding box
(see Photo 4), made on a principle described in " Shielding
packing ". The
device with a source of necessary electric currents and voltage looks as is
shown on Photo 5. We name
they be - Converter-B
|
Photo 3 |
Photo 4 |
Photo 5 |
In the given device the plait from two conductors, in varnish isolation, diameter
0.12 mm, length 14 m. the Counter current in conductors - 120 мА. Voltage between
wires 330V.
Windings it is covered by a thin
layer of colophony dissolved in alcohol. In a shielding box the standard
cardboard glass with water or other objects is located for charging.
Approximate time exposition 10-20 minutes.
It is necessary to notice that is
probable from voltage between conductors, the threshold internal energy of the
DSS cluster at which it is liberated depends. I.e. changing this voltage, we
change internal characteristics liberated of the clusters and, as consequence,
character of influence of these DSS clusters on the environment in which they
will appear.
The sensation person of the DSS clusters
depends on degree twisting conductors. Similar action occurs and at change of a
relation of counter currents in conductors.
Some thoughts:
1) it is probable,
matters not only itself twisted conductors in a plait. Possibly, matters
braiding deformations of the most copper conductor.
2) it
is probable, in DSS clusters in the given design to occur replacement some of
the DSS electrons on the usual. How it to check
up?
3) it is
probable, in DSS clusters in the given design to occur inclusion of protons isolated
of rosin molecules (as weak acid). How it to check
up?
|
If you wish to
make the experiments, but are at a loss in independent manufacturing of the
Converter, you can order its manufacturing. Information
on E-mail: alexandrshpilman78@gmail.com |